How to Cut Roof Rafters

If you’re framing a gable roof on a new house, or building a shed or even a doghouse with a gable roof, you’ll need to cut a number of roof rafters. The roof rafters provide integral structural support to the roof. Before you cut your boards, you’ll need to measure the width of your building and calculate the exact length of each rafter. When you cut the rafters, you’ll need to make 3 separate cuts: the ridge cut (also called the plumb cut) at the top of the rafter, the birdsmouth cut (which itself comprises 2 different cuts) where the rafter meets the building’s wall, and the tail cut, at the base of the rafter.

Things You Should Know

Take measurements of your roof and plug them into a roofing calculator to figure out the length of each rafter.
Make a plumb cut along the top of your rafter with a framing square and a circular saw.
Calculate and mark where the birdsmouth and tail cuts need to go. Birdsmouth cuts go on top of the building's wall, and the tail cut goes at the bottom of the rafter.
Saw through your pre-marked lines to make your birdsmouth and tail cuts.

Part 1

Part 1 of 4:

Calculating Rafter Length

Download Article

1
Measure the width of your building. Before you start cutting, you first need to determine how long your roof rafters need to be, and the angles at which you’ll cut the top and bottom of the rafter. Use a tape measure to measure the entire width of your building. Measure as precisely as possible, down to the ¹⁄₄ inch (0.64 cm), ¹⁄₈ inch (0.32 cm) , or ¹⁄₁₆ inch (0.16 cm) .^{[1]XResearch source}
- For example, the width of the building may be 72.75 inches (184.8 cm).
- Use a pencil to jot the width down somewhere. Write on a spare sheet of paper or a section of exposed wood.
- Making these measurements 2 or 3 times is a good way to ensure accuracy.
2
Subtract the width of your ridge beam. The ridge beam is the vertical piece of plywood which will form the peak of the gable, and to which you’ll fasten the rafters on either sides. Measure the width of the ridge beam: if you’re using a 2x4, it’ll measure 1.5 inches (3.8 cm). Subtract this measurement from the width of your building.^{[2]XResearch source}
- So the new width measurement will be 71.25 inches (181.0 cm). Jot down this “adjusted” width measurement as well.
Advertisement
3
Divide the adjusted width measurement by 2. Since each individual rafter will only span half of the building’s width (minus the width of the ridge beam), divide the adjusted width measurement in half.^{[3]XResearch source}
- So, the example halved width measurement will be 36.63 inches (93.0 cm).
- The final measurement is referred to as the “run” of a building. Write the run measurement down alongside the other measurements.
- If you’re using a roofing calculator, press the “Run” button to input the run measurement in the calculator’s memory.
4
Calculate the roof pitch. The pitch of the roof is a ratio: the number of inches that the roof rises vertically for every foot of roof. This is a way of measuring the degree of steepness of the roof. So, use a tape measure to find the height of the roof above the top wall of the building. Also measure the length of half of the roof from one side of the ridge beam to the edge of the building. If the roof rises 7 inches (18 cm) for every 1 foot (0.30 m), its pitch would be written as 7/12.^{[4]XResearch source}
- If you’re using a roofing calculator, press the “Pitch” button to input the pitch ratio in the calculator’s memory.
5
Determine the length of each rafter. If you’re using a roofing calculator, it will use the information you’ve already input (run measurement and pitch) to calculate the length for each rafter. Press the “Diagonal” key, which will calculate the diagonal measurement between your structure’s outside wall and the top of the ridge beam. Write down this diagonal measurement. In this example, it will be 39.81 inches (101.1 cm).^{[5]XResearch source}
- If you’re not using a roofing calculator, you’ll need to perform some complex trigonometry to calculate the rafter length. You’ll also need to purchase a copy of a roofing ready reckoner: a manual with rafter length tables.
- Roofing calculators are commonly used by professionals. If you’d rather not purchase one, there are many available for free online. For example, there’s a free roofing calculator at: https://www.roofcalc.org/roof-rafter-calculator/.
- Keep in mind that, if you want your rafters to overhang past the edge of the building wall, you’ll need to add that measurement in separately. The calculator (or math equation, if you’re writing it out longhand) will only calculate the diagonal measurement to the edge of the building.
6
Calculate the rise of your roof. The “rise” is the vertical measurement that indicates how tall the roof will be at its highest point above the walls of the building. The rise is the exact height of the ridge beam.^{[6]XResearch source} If you’re using a roofing calculator, press “Rise,” and it will calculate the value.^{[7]XResearch source}
- If you’re not using a roofing calculator, simply subtract the height of your walls from the total height of the roof at its peak.
- The example rise will be 17.81 inches (45.2 cm). Jot down this number alongside the others you’ve already written.

Part 2

Part 2 of 4:

Making the Plumb Cut

Download Article

1
Fix stair gauges on the framing square to mark the pitch. So, if the pitch of your roof is 7/12, place one stair gauge on the vertical part of the framing square (the “tongue”) at the 7 inches (18 cm) mark, and place one stair gauge on the horizontal part of the framing square (the “body”) at the 12 inches (30 cm) mark. This will give the framing square the angle you need to make the ridge cut.^{[8]XResearch source}
- You can purchase both stair gauges and a framing square at your local hardware store.
2
Mark the plumb cut at the top of the rafter. The plumb (or ridge) cut is made at the top of the rafter. Choose which end of your rafter you want to be the top. Set the framing square on top of the rafter beam, with the tongue facing the top of the rafter. Then, use a pencil to trace the outside edge of the framing square’s tongue.^{[9]XResearch source}
- Since you’ve attached stair gauges to the framing square, the line you’ve drawn will be at the correct angle for the rafter to lay flat against the ridge beam.
3
Saw along the line you’ve marked to indicate the plumb cut. Using a handsaw or a circular saw, cut the rafter along the line you’ve just marked. Be sure to follow the line exactly, or you’ll have an uneven plumb cut.^{[10]XResearch source}
- Clamp the rafter to a workbench or sawhorses before cutting to ensure stability. C-clamps would work well for this.
- If you’re using a handsaw, grasp the handle firmly in your dominant hand. Saw back and forth using the full length of the blade.

Part 3

Part 3 of 4:

Measuring and Marking the Birdsmouth and Tail Cuts

Download Article

1
Measure the diagonal of the rafter. Start this measurement from the top (the long end) of the cut you just made. When the rafter is installed, this top/long end will be at the peak of the ridge beam. Hook your tape measure on to the rafter, and measure the diagonal rafter length that you calculated earlier. Use your pencil to mark the length directly on the rafter.^{[11]XResearch source}
- The diagonal measurement is the full length of the rafter, minus the overhang. Measuring the diagonal will allow you to make the tail and bird's mouth cuts in the correct locations.
- In this example, the diagonal measurement that you found earlier was 39.81 inches (101.1 cm).
2
Position the framing square to make the birdsmouth cut. Align the framing square so that the stair gauge that you’ve placed on the tongue (short edge) of the framing square is on the pencil mark you made to indicate the full diagonal length of the rafter. Hold the long end of the framing square so that the other stair gauge is also resting against the rafter; this will ensure that you mark the tail cut at the correct angle.^{[12]XResearch source}
- Use your pencil to trace the full length of the tongue along the width of the rafter.
3
Determine the depth of the birdsmouth cut. This is relatively simple: measure the full width of the outside wall. For most buildings, the birdsmouth cut is 4 inches (10 cm) deep.^{[13]XResearch source} The width of the 2x4 used to frame the outer wall measures 3.5 inches (8.9 cm), and the outside sheathing measures ¹⁄₂ inch (1.3 cm).^{[14]XResearch source}
- Sheathing is the term used for the board or panel that forms the outer surface of a building.
4
Position the body of the framing square on the rafter. Use the body (long side) of the framing square. Rotate it 180° from how you’ve been using it (so the right angle is pointing up). Set it so that the 8-inch (20 cm) mark on the body of the framing square intersects the line for the tail cut. This will provide a 4 in (10 cm) birdsmouth cut.^{[15]XResearch source} Use your pencil to trace this line onto the wood.
- If your bird's mouth cut is not 4 inches (10 cm) deep, slide the framing square to shorten or lengthen the length of the cut accordingly. ^{[16]XResearch source}
5
Measure the rafter overhang. If, for example, you want the rafter to overhang the edge of your building by 6 inches (15 cm), measure this now. Keep the framing square in the position that it was set in to measure the birdsmouth cut. Slide the framing square until the 6 in (15 cm) mark intersects the line you’ve marked for the birdsmouth cut.^{[17]XResearch source}
- Overhang is the portion of the rafter that will extend past the edge of the building’s wall. This will lengthen the total length of the rafter by 6 inches (15 cm), bring the new total length to 45.81 inches (116.4 cm).
6
Trace the tail cut. Keep the framing square in the same position, and use your pencil to trace the tongue (short side) along the surface of the rafter. (The stair gauges will hold the framing square at the proper angle.) This will mark the tail cut: the very end of your rafter, with the 6 inches (15 cm) overhang built in and the birdsmouth cut neatly marked.^{[18]XResearch source}
- Now all that’s left is to cut the rafter accordingly.

Part 4

Part 4 of 4:

Making the Birdsmouth and Tail Cuts

Download Article

1
Saw along the line you marked for the birdsmouth cut. Be very precise with this cut since, unlike the plumb cut, you can’t saw all the way through the board. Carefully follow the lines you’ve marked for the tail cut so that it maintains the specific measurements and angles.^{[19]XResearch source}
- For added stability when making the birdsmouth and tail cuts, use C-clamps to clamp the rafter to a workbench or sawhorses.
Using your handsaw or circular saw, cut precisely along the line that you’ve marked for the tail cut. The excess rafter material will fall off as you complete this cut, leaving you with the finished rafter.^{[20]XResearch source}
3
Repeat the process for your other rafters. At this point, you’ve cut 1 roof rafter. Depending on the size of your structure, you will need to cut several (or many) more. All roof rafters should be identical, so follow the same steps to measure the plumb cut, tail cut, and birdsmouth cut.^{[21]XResearch source}
- The number of rafters needed will be determined by the length of your roof. Rafters are commonly spaced about 24 inches (61 cm) apart. Refer to this chart for more detailed rafter-spacing information: https://www.mycarpentry.com/rafter-span-tables.html.
- Keep in mind that you’ll always need an even number of rafters.

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Always take safety precautions when working with any type of saw. Keep your hands away from the blade, and wear safety goggles or other protective eyewear.
Thanks
Helpful3 Not Helpful0