Download ArticleDownload ArticleX
This article was co-authored by Ricardo Mitchell. Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience.
This article has been viewed 158,395 times.
This How.com.vn will show you how to create an ethernet cable at home.
Steps
Download Article
Strip your cable. Use your cable strippers at about 1-2 inches from the end of the cable to remove the outer jacket.
Untwist the twisted pair wires all the way back to the jacket. This can be done just like a regular twist-tie on a loaf of bread, but with four of them of different colors.Advertisement
Align the untwisted wires in the order necessary for your needs. For this scenario, you'll be making a straight-through cable, which has both ends of the cable with the same alignment of wires, so it's easy enough to do. Since this is your first cable, we'll consult the cheat sheet to know what order we're aligning in!
Cut the extra wire. Once you've untwisted the wires, you'll have a superfluous amount of copper wiring left; we don't need this much, but it's good to have it in the previous step to help in aligning the colors properly. Use the wire-cutting scissors to cut these off.
Push the remaining wires into the RJ45 head. Be careful not to bend the wires while pushing them in or you run the risk of creating a bad cable. You also don't want too little or too much wire left in the head; there's no definite length necessary, but it's pretty obvious to tell if there's too much cable or not enough. A short length of the jacket should be up the RJ45 head; use this knowledge as a reference.
Double-check that the wires are all the way up into the gold pins of the head and made it up in the proper order. (Consult your cheat sheet if needed!)
Push the head into the open space of the crimping tool and squeeze it closed, hard. If you don't crimp the cable all the way, the head may come off.
Open the crimping tool and remove your newly-crimped Ethernet connector.
Repeat the crimping process on the other side of the cable if you're making a completely new cable. If you're repairing one end, this won't apply to you, so move on.
Plug one end of the cable into the tan, two-port end of the cable tester, and the other end into the other part of the tester with the graphic display window. Turn it on and listen for the beep. If it beeps once, you successfully made an Ethernet cable; if it beeps twice, some part of the cable is messed up and needs repairing. Depending on the error, the cable may or may not still be usable.
Plug your Ethernet cable in. Now that you've made an Ethernet cable all by yourself, you can connect all kinds of devices together! Of course, for the cable you just made, make sure they're different devices! You can connect to Xbox Live now, to Playstation Network, to your wireless router, and many more devices you don't even know about! Or, if you're known as the life of the party, you can show off to your friends and never have to worry about being invited to another party again... !
Advertisement
Community Q&A
Search
- QuestionCan the same port be used for a 2.0 and 3.0 USB connector?
Community AnswerEthernet cables cannot run through USB ports. USB ports and Ethernet ports are completely different and have different functions. - QuestionDo longer Ethernet cables reduce connection speed?
RupertTop AnswererYes, but not to the extent that you'll ever notice. Ethernet cables lose speed over massive distances. There will be no significant difference between a cable that travels the length of your house and one that's connected to a device right next to the router.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
SubmitAdvertisement
Video
Tips
- Many times, the error with making these cables comes from the wires not making it in the gold pins far enough, so it's important that they're all the way in.Thanks
- Keep the RJ45 head with the protruding clip facing down relative to you. Also, if you accidentally bend the wires while pushing them into the head, you risk creating Electromagnetic Interference if the copper becomes exposed, which lowers the quality of the cable.Thanks
- Use your thumbnail to determine how much wire to keep when you cut the extra off; remember to keep a death-grip on these wires to keep the alignment proper.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Warnings
- There's a reason you need eye-protection: when cutting the copper wires, they can go flying and potentially get your eye! Be smart, be safe!Thanks
Advertisement
Things You'll Need
- Appropriate length of Cat5e Ethernet cable
- Safety goggles (or glasses if you have those)
- Wire-cutting scissors
- Cat5e RJ45 head(s)
- Crimping tool
- Cable strippers
- Ethernet cable tester
References
- Videos provided by dial2fast
About This Article
Electrician Professional, CN Coterie
This article was co-authored by Ricardo Mitchell. Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience. This article has been viewed 158,395 times.
How helpful is this?
Co-authors: 9
Updated: August 24, 2023
Views: 158,395
Categories: Networking Hardware
Thanks to all authors for creating a page that has been read 158,395 times.
Reader Success Stories
Is this article up to date?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
Advertisement
