How to Clean Aluminum for TIG Welding

TIG welding is one of the preferred methods of welding aluminum because it creates strong, attractive welds. Pieces of aluminum are often covered in oil and grease as well as surface oxides, so cleaning the aluminum is essential before you start welding. Always degrease the aluminum before you scrub off surface oxides. With a little patience and the right tools and techniques, you can clean any aluminum pieces you want to weld together and be confident in the integrity of your welds!

Part 1

Part 1 of 2:

Removing Oil and Grease

1
Use acetone or lacquer thinner to degrease aluminum. Acetone and lacquer thinner are natural solvents that are safe for aluminum and work well to remove oil and grease from surfaces. Methyl ethyl ketone and toluene are 2 alternative solvents that you can use. Don’t use alcohol to degrease aluminum because it is not an effective degreaser.^{[1]XResearch source}
- Contaminants like oil and grease contain hydrogen, which can cause weld porosity if they come into contact with your welding arc.
- You could also use a commercial degreaser that is made for aluminum, as an alternative to a solvent. If you do so, choose one that is biodegradable and environmentally friendly.
Warning: Always start cleaning aluminum by degreasing it. Don’t try to clean it right away with something abrasive like a wire brush, or you will just spread the oil and grease around and create small scratches on the surface that contain contaminants.
2
Open up doors and windows to ventilate your workspace. Create as much ventilation as possible, so you aren’t breathing in excessive fumes from the solvents. Breathing in large amounts of solvent fumes can cause lung, throat, and nose irritation.^{[2]XResearch source}
- If you can’t open up any doors or windows to get some airflow in your workspace, take the aluminum somewhere outside to degrease it.
- If you ever feel dizzy when you’re working with solvents, stop immediately and leave the area to avoid breathing in more fumes.
3
Put on gloves and protective eyewear. Wear work gloves, rubber gloves, or latex gloves to protect your skin from the solvent. Use safety glasses or goggles to protect your eyes.^{[3]XResearch source}
- Some solvents can cause skin and eye irritation, so always take the proper safety precautions before working with solvents.
- If you ever get a solvent splashed in your eyes, stop working immediately and go flush your eyes out under cool running water.
4
Dip a clean, lint-free rag into your chosen solvent. Pour some of the solvent out into a container. Hold the cloth and submerge it in the solvent to saturate it.^{[4]XResearch source}
- A microfiber cloth works best for this. You could also cut up an old, clean T-shirt to make some lint-free rags.
5
Wipe down all the parts you plan to weld with the solvent-soaked rag. Rub the rag in circular motions all over every surface of each part that you are going to weld. Re-wet the rag as you go if the parts are large and you need more solvent.^{[5]XResearch source}
- It’s important to be very thorough and wipe down all the surfaces of each piece of aluminum, rather than just around the area where you are going to weld. Oils and grease can get spread around very easily, so make sure the aluminum is completely degreased.
6
Wait 5-10 minutes for the solvent to evaporate before you proceed. Leave the aluminum pieces to dry for 5-10 minutes before you continue to clean the aluminum. Solvents evaporate on their own very quickly, so you don’t need to worry about drying the pieces by hand.^{[6]XResearch source}
- Never weld any parts right after degreasing them. If solvents come into contact with your welding arc, they can release poisonous gases.
Advertisement

Part 2

Part 2 of 2:

Getting Rid of Surface Oxides

1
Use a stainless steel brush with soft, fine bristles to clean the aluminum. A manual or power brush will work for removing surface oxides. Don’t use brushes with large, stiff bristles, as these will burnish the oxides instead of removing them.^{[7]XResearch source}
- Make sure that the brush is clean, so you don’t transfer any contaminants to the aluminum.
- Surface oxides are a form of corrosion that metals form due to contact with the air and moisture in the air.
- Visible rust occurs on metals when there are high levels of oxidation, but oxide layers start to form whenever metal sits out in the air. This means that your aluminum pieces can have surface oxides even if it doesn’t look like it.
2
Apply white vinegar to the aluminum using a clean, lint-free cloth. Vinegar is a weak acid that works to deoxidize aluminum. Soak a clean, lint-free cloth, such as a microfiber cloth, in white vinegar and rub it all over every surface of the aluminum parts you plan to weld.^{[8]XResearch source}
- You could also put the vinegar into a spray bottle and spray it directly onto the aluminum, rather than wiping it on.
Tip: You can use a commercial oxide remover as an alternative to vinegar. These commercial solutions contain a blend of detergents and acids for removing oxides and come in a spray bottle or jug.
3
Scrub all surfaces of the aluminum pieces gently with your wire brush. Press the brush lightly against the aluminum. Rub it in circular motions, applying gentle pressure the whole time, all over the aluminum pieces you plan to weld to rub the vinegar in and scrub off surface oxides.^{[9]XResearch source}
- Applying too much pressure can burnish surface oxides and actually drive them further into the aluminum surfaces, so always scrub gently.
Rinse the aluminum piece under running water or spray it down with a hose, depending on how big it is, to clean off the vinegar. Dry it off thoroughly with a clean, lint-free cloth.^{[10]XResearch source}
5
Wrap the aluminum in kraft paper and tape it up if you won’t weld it right away. Cover each aluminum piece in kraft paper to protect against dirt and grime. Tape the paper up using packing tape or masking tape to seal the aluminum inside.^{[11]XResearch source}
- As long as you protect the aluminum this way, you can weld it any time in the next 3-4 days or so. If you leave it longer than that, clean it again before you weld it to remove surface oxides.
Advertisement

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

You can clean aluminum perfectly well with natural solvents and vinegar, so you don’t have to buy any special commercial cleaners. If you do want to use a commercial degreaser or oxide remover, try to find varieties that are natural and environmentally safe.
Thanks
Helpful0 Not Helpful0

Warnings

Always wear gloves and protective eyewear and work in a well-ventilated space when you work with solvents to avoid breathing in the fumes and getting the solvent on your skin or in your eyes.
Thanks
Helpful0 Not Helpful0
Always degrease aluminum before you move onto removing surface oxides, or you can end up just spreading oil and grease around and making it harder to remove.
Thanks
Helpful0 Not Helpful0