How to Block a Floyd Rose Tremolo

Blocking your Floyd Rose tremolo or “hard-tailing” is a quick, reversible modification for when you would prefer to not have a tremolo bridge installed on a guitar. The benefit is that pulling notes on your fretboard will not de-tune other strings! The cost is the ability to use your whammy bar for any tremolo effect (no more Eddie Van Halen dive-bombs!). All you will need is a small block of wood, a screwdriver, and the equipment needed to change your strings. If you’re not totally confident about your ability to perform this modification to your instrument, you may want to talk to a qualified technician.

Part 1

Part 1 of 3:

Loosening Your Tremolo

Download Article

1
Remove the tremolo bar’s cavity cover on the back of the guitar. Using a Phillips screwdriver, carefully remove all 6 screws holding on the cavity cover. Lift off the cover.^{[1]XResearch source}
- Set the cover and screws aside in a safe place, so nothing gets lost.
2
Remove all of the strings from the guitar (optional). Use your guitar string winder to loosen and detach all of your strings from the headstock. Use your guitar string cutter to clip of the curly frayed ends of each string. Press your strings down through the bridge until they poke out the back. Pull on the bottom end of each string and slide it all the way through the bridge.^{[2]XResearch source}
- Some technicians advocate for removing the strings, while others do not.
- Removing the strings from the guitar removes tension from your tremolo. This can make it easier to fit the block into the tremolo opening.
- Performing this modification with the strings still attached keeps the tremolo in your natural playing position. If you install the block without moving the tremolo, your guitar will be ready to play as soon as you close the back cavity.
Advertisement
Locate the 2 screws at the top of your tremolo (toward the neck of the guitar). Use your Phillips screwdriver to carefully loosen these screws.^{[3]XResearch source}

Part 2

Part 2 of 3:

Creating Your Block

Download Article

1
Measure the open space below the tremolo. Locate the space that sits just below the tremolo (between the spring block and the back of the body cavity). This space is bordered on 1 side by the tremolo itself, and on the other 3 sides by the body cavity. Use a ruler to measure the width and depth of this opening. Write these numbers down.^{[4]XResearch source}
- The length of the opening should be about 1–1.5 inches (2.5–3.8 cm). There is no need to measure this.
You are going to create a small block of wood that will fit in the opening below your tremolo. Start with a 1 inch (2.5 cm) thick wooden plank. Use a ruler and a permanent marker to mark the correct width and depth.^{[5]XResearch source}
3
Use a hand saw to cut your plank of wood. Place your plank of wood on a flat surface, with the portion you plan to cut first pointing up. Steady your plank of wood with your non-dominant hand. Place the sharp side of your saw on the wood, and begin sawing with a backward motion. Move the saw back and forth until you’ve made the cut. Turn your plank and cut the other side.
- Wear gloves and protective eyewear before using a saw.
4
Sand the block you’ve created with 150-grit sandpaper to make it smooth. Run sandpaper over the edge of your block to remove any loose wood or dust. If the block you created is slightly too large, you can also use sandpaper to make it a little smaller.^{[6]XResearch source}
- 220-grit sandpaper will also work.

Part 3

Part 3 of 3:

Installing The Block

Download Article

Your wooden block should drop right into the space below your tremolo. If it is too big, you can sand it down a little more.^{[7]XResearch source}
Use your Phillips screwdriver. You want these screws to be secure, but you still want slack from the tremolo strings to put pressure down on your block.
3
Restring your guitar if you removed the strings. Slide your new strings in through the holes on the back of the guitar. Pull each string up through the tuning key, add about 3 inches (7.6 cm) of slack, and then bend the string sharply to hold it in place. Use a string cutter to remove the excess string, and wind your guitar strings until they have good tension.^{[8]XResearch source}
- You will need to tune your guitar after this.
Place the cavity cover on the back of your guitar. Locate your screwdriver and 6 screws. Carefully tighten the screws on the back of the cavity cover.^{[9]XResearch source}

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Things You’ll Need

Phillips screwdriver
Ruler or tape measure
Pack of guitar strings
Guitar string winder
Guitar string cutter
150-grit sandpaper
1 inch (2.5 cm) thick plank of wood
Saw
Marker

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Wear gloves and protective eyewear when operating a saw.
Thanks
Helpful1 Not Helpful0
Be sure to saw on a flat and stable surface.
Thanks
Helpful1 Not Helpful1
Use a clean, sharp saw.
Thanks
Helpful1 Not Helpful0
When sawing, apply pressure on the downstroke only.
Thanks
Helpful1 Not Helpful0