How to Block Up an External Doorway

If you’ve got a doorway that you never use or you’re looking to enclose a room, blocking up the doorway is an effective and relatively inexpensive way to do the job. It’s also not super difficult if you have the right materials. To make the job a little easier, we’ve answered a few of the most common questions that folks have about what it takes to block up an external doorway.

Question 1 of 5:

How do you fill a doorway?

Download Article

There are many different reasons for wanting to fill a doorway, such as moving the door from one part of the wall to another or sealing off a door that you no longer need. Whatever your reasons, the simplest and perhaps the most effective way to fill an external doorway is to block it off with cinderblock or concrete blocks.^{[1]XResearch source}

Question 2 of 5:

How do you install an exterior door block wall?

Download Article

1
First, you need to remove the door frame. Start by removing the hinges and taking off the door if you haven’t already. Saw through the jambs until the saw reaches but doesn’t touch the actual wall. Then, use a chisel or a crowbar to pry off the jambs. Once the jambs are removed, use your chisel or crowbar to pry off the wooden frame so you’re left with a clean opening in your wall.^{[2]XResearch source}
- Don’t try to block up the doorway without removing the frame or your wall won’t be as strong.
2
Stack cinderblocks in the opening with frame ties between each row. Cinderblocks are relatively lightweight, strong, and cheap. Install the bottom row of blocks and then screw frame ties to the walls just above the row of blocks and stack another row of blocks on top. Continue stacking blocks and installing frame ties between each layer so your blocks are also supported by the surrounding wall.^{[3]XResearch source}
- Use a timber saw to cut any blocks to size.
3
Plaster over the block wall for a smooth finish. Mix your plaster in a bucket and use a hand trowel to spread it over both sides of your block wall to form a base coat. Allow the first layer to dry and then apply a second layer, known as the skim plaster. Make the second layer thick enough so it’s even with the surrounding wall. Allow the plaster to fully dry and harden.^{[4]XResearch source}
- Follow the mixing directions on the packaging of the plaster.
- Check the packaging of the plaster for specific drying and curing times.

Question 3 of 5:

How many blocks do I need to use?

Download Article

You can divide the wall square footage by the block square footage. Measure the opening of the doorway and multiply the width by the height to get your square footage. Then, measure the width and height of your blocks, multiply the values together and divide them by 144 to get their square footage. Once you have both values, you can divide the wall square footage by the block square footage to figure out how many blocks you need to fill the space.^{[5]XResearch source}
- The standard cinderblock is 16 inches (41 cm) wide by 8 inches (20 cm) high.
- For example, if your wall is 3 feet (0.91 m) wide and 9 feet (2.7 m) high, then you’d multiply them together to get 27 square feet (2.5 m²). If you’re using a standard cinderblock, then your block measurements are 16 inches (41 cm) wide by 8 inches (20 cm) high. Multiply those values together to get 128 inches (330 cm), which you then divide by 144 to get .89 square feet (0.083 m²). Finally, divide 27 square feet (2.5 m²) by .89 square feet (0.083 m²) to get 30.33, which you could round up to get 34 cinderblocks.
- You can also use an online block calculator at: https://www.inchcalculator.com/concrete-block-calculator/

Question 4 of 5:

Do I need a permit to block up an external door?

Download Article

Yes, many locations require a permit for exterior door replacements. However, the regulations can vary from location to location. Plus, your neighborhood association may have its own regulations that you need to adhere to. It’s always better to be safe than sorry. Before you start blocking up your door, look up the local rules and regulations regarding building permits as well as the bylaws of any neighborhood associations that you’re a part of to see if you need to obtain special permission.^{[6]XResearch source}
- If you’re required to get a permit but you choose not to, you could face a hefty fine.

Question 5 of 5:

How much does it cost to close up a doorway?

Download Article

Of course, the cost can vary depending on the size of your doorway and how many blocks it takes to fill it in. If you do the project yourself, you can save on some labor costs, but if you choose to hire a professional, you’ll have to pay more to cover their costs. Additionally, you may need to pay for special permits, which could also drive up the cost.^{[7]XResearch source}

Expert Q&A

Search

Add New Question

Question
What is the best way to block a doorway?
Ryaan Tuttle
Home Improvement Specialist
Ryaan Tuttle is a Home Improvement Specialist and the CEO of Best Handyman, Inc. in Boston, Massachusetts. With over 17 years of experience, he specializes in building home service businesses, focusing on creating scalable and efficient brands. With the help of his global team, the companies have achieved over 10+ million in sales and received recognition through magazine features, and enjoy partnerships with How.com.vn and Jobber field service software. Boston Magazine and LocalBest.com have named Best Handyman Boston the Best Handyman in Boston. Ryaan holds Construction Supervisor and Home Improvement Contractor Licenses.
Ryaan Tuttle
Home Improvement Specialist
Expert Answer
For me, the best way to block up a doorway is to cover it with wood framing and then adding drywall over it.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 8