How to Bleed an Oil Furnace

An in-depth guide to safely and effectly bleed your oil furnace

If you’ve tried the furnace reset button, checked to make sure there is fuel oil and your furnace still won’t start, don’t fret. Before you call the repairman or start shopping for a new furnace, check the fuel source and make sure the line to the furnace is void of air. Running low on or being out of fuel can cause a furnace to not restart even after you replenish the fuel supply. You may simply need to bleed an oil furnace line and start it up again.

Part 1

Part 1 of 2:

Prepare to Bleed the Furnace

Download Article

Turn the furnace off before starting any work on the fuel pump.^{[1]XResearch source} Depending on your model, you may need to flip a switch near your furnace or turn it off at the breaker. You should also turn off the gas using the shut-off valve connected to the gas line.
The screw is usually a small nipple-like screw.^{[2]XResearch source}
Advertisement
3
Place a small bucket or pan under the bleed screw. The bucket will catch any fuel that sputters out as you bleed an oil furnace.^{[3]XResearch source}
- If the screw is in an area that is impossible to put a bucket or small tray under, use a flexible tubing just big enough to fit over the bleed screw. Place the tube over the bleed screw and direct it to an area where you can fit the tray or bucket.

Part 2

Part 2 of 2:

Bleed the Furnace

Download Article

Make sure the screw remains on the pump and is only a little loose, so it doesn’t fall completely off when you bleed the oil furnace.^{[4]XResearch source}
2
Push the reset button on the furnace to turn it back on. As the furnace starts to suck fuel in, air and fuel will spit out of the bleed screw.^{[5]XResearch source}
- Keep your pliers or wrench on the screw ready to tighten it. This will also ensure the screw remains in place, if you did loosen it too much.
- If the furnace cycle ends before the air and fuel mixture stops sputtering, you’ll need to push the reset button again to continue the bleed process until the furnace pushes out all the air from the line.
- Some furnaces may have a lockout system that won’t allow you to reset more than one or two times. If this happens, you can override the lockout by holding the reset button in until the furnace kicks in again.
Be careful not to tighten it too much. Replacing a stripped bleed screw can be a very costly project.
It should run normally without problems now. If it doesn’t restart the next time, check the line for air again by repeating the bleed process. You may not have gotten all the air out the first time, or you may have a debris blockage in your fuel line.

Community Q&A

Search

Add New Question

Question
Part one, step one, says to turn off the furnace, but part two says to hit the reset button. I have to turn it back on right? What was the point of turning it off?
Community Answer
Yes this is a mistake. Furnace should be on, and fuel is only pressurized when reset cycle is activated.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 15
Question
I have bled and pressed the reset button and it still doesn't work. What should I do?
Community Answer
It may take more time than expected. I just did this, and it took about 8 reset/bleed cycles, and about 15 minutes. I had to wait a minute or more before each reset. Each bleed was maybe 1/4 to 1/2 cup oil, plus air, so it filled 2/3 of a large yogurt container. It was just starting to get frustrating when I heard the burner finally light.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 4 Helpful 27
Question
How tight do I close the bleeder valve?
Johnny The Critic
Community Answer
Tight enough so that oil doesn't leak out. Hand tight should be good, then just a smidgen more. Be very careful not to over tighten. A stripped bleeder valve will be a costly repair.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 5 Helpful 8